10 foot sailboat plans

or

- WOOD EPOXY

RETURN TO  HOME PAGE

• About Modern Wooden Boats
• Tips & tricks
• What’s inside a boat plan ?

Idea 21 sportboat

The development of the family of small offshore capable sailboat plans : chined hull for the highest stability, vertical lifting keel, trailerable, suitable for club racing or cruising (two interior versions) ,  plywood and epoxy hull with the radius chine system, sparkling performances while sailing and reasonable interiors for coastal cruising.

First boat launched : read the first impressions here

Idea 21 small sailboat plan is the latest development of my family of small plywood & epoxy sailboats plans for homebuilders : it was quite a time since i was thinking of an evolution of her smaller 19 footer sister, so i finally take the decision to publish this new plan. the goals of this plan is simple: add interior volume, simplify the work for homebuilders switching to a complete plywood & epoxy radius chine hull, enhance slightly the sparkling performances of idea 19, keeping the sailboat very balanced and suited for sailors ranging from enthusiast beginners to experienced seamen., first boat launched and several other boats in building stage make idea21 the most sparkling project on our catalogue,  hull: chined hull on a small light sailboat has a simple reason to exist: it gives more stability to the sailboat when heeled, much more than a round hull similar sailboat. i managed to keep a very low wetted area of the unheeled hull, in order to achieve a good pace in light air and avoid excessive drag. stern sections are quite flat to gain speed downwind (idea 19 has been clocked with speed steadily in excess of 15 knots)., bow sections: experiences on racers showed that “knife-blade” bows may give you less resistance, but the price to pay is high in terms of buried bow sailing downwind, so i decide to provide this plan a large u-shaped section on the bow ; sails provide the sailboat plenty of power to defeat the small amount of added drag., sailplan: i have a very good starting point with idea 19, so we’re doing small adjustments and no revolutions: square top mainsail, 7/8 fractional rig , very wide single swept spreaders, no backstay, deck stepped mast with sturdy section, 110 % j jib, code zero, jennaker hoisted on swinging retractable bowsprit, and a good amount of sail area., keel and ballast: idea21 have a solid hard wood cored & unidirectional glass epoxy laminated lifting keel, with a naca optimised profile and a low resistance hydrodynamical shaped 280 kg lead bulb bolted on the keel tip; it can be made by a homebuilder, no need for professional welder; the fin area is on the low side, speed will help generating the required lift without adding too much drag. keel case is in 20 mm thickness plywood and epoxy laminated glass reinforcements, and it’s perfectly waterproof while sailing., full lifting keel  version : after a request from a builder, idea 21 cruise is available in a version featuring an integral watertight keel case running form hull bottom to cabin top panels, this feature called flk (full lifting keel) will allow the boat to sail with keel partially raised or to motor with keel totally up, a good option if you sail in shallow waters frequently., cockpit: was one of the strongest point in idea19, we simply keep the same arrangement and dimensions, so we have a really huge area for the crew and a simple and sturdy building in plywood panels epoxy glued on a structure of bulkheads and stringers., interiors: here i focussed on several upgrades; i decided to split the project in two versions (so two different sets of plans, you have to specify on order), “sport cruise” or “racing” ; both versions have 4 berths, a classic v berth on bow and two quarter berth after; in the cruising version cabin is 55 cm longer, giving wider interiors, enough room for a separate toilette and more comfortable after berths ; in the racing version we have a marine toilet (there’s room for a jabsco compact one) under the bow v-berth; cabin height is 1.65 m in both versions. interiors plywood panels are detailed on plans., taking advantage form the first season of sailing, i can now say that i strongly advice the cruise version as long as you are not going to run a sailing school, thus needing extra space in the cockpit., wooden rig: starting form summer 2019 we deliver two extra drawings with the plans, both for race and cruise version,  describing how to build a wooden rig suited for this boat.  keep your budget low at the price of a small extra weight , how to build the boat: we chose the plywood & epoxy resin “radius chine” system, as for petrel 28 and hirundo 750, so the hull planking is in okume marine grade plywood ; planking the hull is quite fast , and the internal structure of the boat is made by plywood bulkheads, floors and solid wood longitudinal stringers, all glued with epoxy and strengthened with epoxy laminated glass tape, assembled on a cheap wood scaffold, keeping the hull light, sturdy and quite easy to build for homebuilders ; the goal is to keep the total weight of the 19 footer, raising the ballast fraction of the sailboat at the same time. here are a couple of pictures of the first planked hull perfectly showing the radius chine planking system.

a HUGE Thanks to Nils Theurer    ([email protected])   for the awesome pictures taken during the first sea trials  

Plans availability: Plans are available in italian and english. Plans are available in imperial units upon request (send me a mail before purchase).

Sailboats embody the mystery of the sea, of going only where the wind is willing to take you. We offer a variety of sailboat sizes, using several construction techniques. We offer sails, hardware and rigging for many of our sailboat designs. This enables you to focus on building your boat, not searching around for all the bits and pieces needed to complete the project.

Free online book: 

• Rigging Small Sailboats
• Sailboat Hardware Notes

Glen-L 25 - Plywood

• Basic Kayaking Knowledge , Learn

15 Free Boat Plans You Can Build This Week (with PDFs)

Boatbuilding is one of the most ancient forms of craftsmanship still alive today. As long as our ancestors have had a curiosity about exploring open waters, they have been practicing and honing their boatbuilding skills.

To be honest, however, building a boat is no small task. It will require a lot of work and patience to ultimately create a finished product that you are happy with and that is actually seaworthy.

Of course, we have also included a few free boat plans. You can keep in your back pocket for the next time you are asked to build a cardboard boat as part of a contest or lakefront teambuilding adventure.

We hope that these resources help you in your journey to build your own boat!

Photo by SeventyFour via Shutterstock

Free Boat Plans

• The Wanigan
• The Slipper

The Handy Andy

• The Jolly Roger
• The Hobby Kat

The White Duck

• The Sea Midge

The Crazy Cardboard Boat

Why Build Your Own Boat?

Photo by Halsey via Shutterstock

There are a lot of reasons why you should explore building your own boat versus buying a pre-made model. Here is a quick breakdown of the most obvious benefits:

• You will know the ins and outs of your finished boat better than anyone
• It can be a great project to work on with your teenage or even adult children
• You will gain valuable skills molding and shaping wood and other materials
• You can design your boat for your specific needs
• You don’t have to trust the sometimes-questionable manufacturing of mass-produced boats
• You can create a boat that functions as your second home on the water
• You can save money if you source materials mindfully

Of course, most first-time boatbuilders still experience some level of trial-and-error. With patience and perseverance, however, you can craft a one-of-a-kind vessel that has no equal anywhere in the world.

Free Boat Plans You Can Build This Week (with PDFs)

1. the wanigan.

PC Duckworks Boat Builders Supply

The Wanigan boat began as a garvey design, which is one of the older boat plans known to the Americas. Traditionally, these boats were built as work scows and were very popular among American summer camps.

The design itself is very simple, but these boats can carry heavy loads. It can also handle a trolling motor being mounted to the stern so you can cover more ground if you want to use it as a fishing boat.

The creator of this boat plan became aware of some of the downsides of the garvey design, such as the heavier weight that made it less efficient than some other designs. So he combined elements of dory and wanigan designs to create a hybrid.

The main changes include an enlarged beam, tilted lathes to provide a stiffer hull, and knocking off the top strakes to reduce the boat’s overall weight.

The Wanigan text

These additional The Wanigan drawings   may also prove useful for your build process!

2. The Mouse

The Mouse is one of the most compact and nimble boat plans we have found for this list. It is an easy build and also a great boat for two kids or a single teenage paddler.

The original builder began with a one-sheet boat design in an effort to create the lightest and most affordable boat possible. This means it is only suited for calm waters and should not be used in high winds or wavy conditions.

That said, it was built in roughly 12 to 24 hours of work time and doesn’t require a full workshop to construct. The main material that is required for building this boat is quarter-inch plywood. But the builder recommends using one-inch by half-inch pine or something a little sturdier.

The plywood and pine components are held together using a method called ”˜stitch and glue’. This method requires choosing one of the best glues for kayak outfitting , which are typically made of epoxy and glass tape rather than something cheaper like polyurethane.

The Mouse Instructions

Also, here are a few extra useful The Mouse Notes for builders

3. The Slipper

The Slipper is the first of many sailboat plans on our list and it is faster, easier, and cheaper to build than most. It also features a deeper cockpit than many other sailboat designs, which makes it safer for intermediate sailors.

This sailboat plan features dual steering stations so that you can sail from inside or outside of the helm. It also includes a centerboard trunk that hardly intrudes into the cabin at all. So that, it is easier to work around while you are in the cockpit.

The exterior hull and cabin of this sailboat feature a modified dory design using two sheets of plywood ripped to three feet wide before being joined together. The resulting hull is a modified V-shape that reduces drag.

The centerboard of this boat can also be winched up to the level of the top of the cabin or lowered down to alter the draft. This allows you to customize the boat design for a stiffer and more weather-worthy vessel if you need it.

The Slipper was also intentionally designed with an aft cabin that naturally helps to keep the bow pointed into the wind whether you are underway or the boat is anchored in the port.

The Building Slipper

4. The Handy Andy

PC DIY Wood Boat

The Handy Andy is a great little 10-foot portable rowboat for hunting, camping, fishing, and other recreational uses. It is actually the only folding boat design on our list, which makes it best for folks that need the most portable boat plan possible.

This boat features a 42-inch beam and a depth of about 15 inches at the mid-section. It also weighs roughly 80 pounds when assembled and can handle up to three average-sized human passengers.

The design boasts a flat bottom with canvas-bound edges and the primary material used for construction is ⅜-inch marine-grade plywood. Despite its lightweight nature, this rowboat can handle trolling motors or even outboard motors with a maximum of five horsepower.

Once finished, the hull can be folded or unfolded in less than a minute’s time.

This design makes it one of the only boats on this list that can be stored in a truck bed or easily carried by two people to be launched at more remote locations.

5. The Junior

If you are looking for an all-purpose dinghy that can handle almost any use you might imagine, look no further than The Junior free boat plan. It can carry three or four average-sized adults and is much easier to row than a traditional dinghy.

It is also durable enough to be equipped with a small outboard motor. You could even set it up with sailing equipment if you want to use it as a sailing vessel. As we said, this is truly an all-around boat design!

This boat plan requires constructing three frames that will provide the majority of the load-bearing support. The builder recommends using ¾-inch framing with ⅜-inch plywood as the exterior material for this boat build.

Resin glue and flathead screws are also required to hold this boat together. But there is a full list of materials included in the plans we have linked to below. Sticking to that plan should also give you enough leftover materials to construct two six-foot oars for rowing this boat until you install a trolling motor or outboard motor down the line!

6. The Jolly Roger

Channel your inner Captain Morgan when you are following these plans to build your very own Jolly Roger boat. This flat bottom boat design is designed for pond fishing . It can also be a useful yacht dinghy for getting from your dock to a larger vessel anchored offshore.

The plan follows conventional dinghy construction methods but also includes a few modifications that will save you time and energy. The wide design is super stable for boaters of all ages.

The keel, frame, chines, and risers are all cut from ¾-inch oak, ash, or any other trusted hardwood you can get your hands on. For the smaller components, the builder recommends using cedar, cypress, fir, or white or yellow pine.

Because this boat plan is also sturdy enough to handle a small motor, it includes important points for protecting the wooden hull from spark plug damage.

Be careful to follow these guidelines to build the safest boat possible if you imagine installing a motor down the line.

The Jollyroger

7. The Cork

The Cork is another simple rowboat design. This one trends away from the flat bottom plans that we have included thus far. Instead, it features a deeper, V-shaped hull that makes it better suited to more efficient rowing and easier maneuverability.

It can be rowed easily from either seating position and is durable enough to handle up to three average-sized adult passengers. The ends of the boat are identical, which allows for multi-directional rowing.

The list of materials required for this boat plan should cost you between $30 and $50, depending on your location and hardware costs there. The resulting build is lightweight enough for two people to be carried and also to be transported on top of a vehicle .

Inside the boat, the builders use aluminum tubing to secure the struts that hold the seats. This material choice keeps the overall weight of the boat down while still adding the necessary rigidity across the beam of the boat.

8. The Hobby Kat

The Hobie Cat is one of the most iconic and recognizable small sailing vessels ever made. This Hobby Kat plan is your answer to building your own iconic sailboat without spending thousands of dollars.

Your finished boat will be able to handle speeds of up to 20 miles per hour. It will be a super fun vessel for windy days on the lake or bay. The builder was able to construct the hulls, decking, and rudder for this boat while spending little more than $200.

From there, they purchased and installed the mast, boom, sail, and rigging, which brought the total amount spent to roughly $650 (still much less than a name-brand Hobie!). Without the mast and sail, this boat weighs roughly 165 pounds and is constructed using primarily 3/16-inch marine plywood.

You can also elect to build your own mast, boom, and sail if you have the time and skills to do so.

Those elements are not included in this boat plan, but they do offer some recommendations for where to buy these components!

The HobbyKat

9. The Tern

Named after the common seabird found around the world, the Tern is a lightweight and nimble sailboat with a 72 square foot base design. She is made for inland sailing and planes very well in moderate breezes.

The hull design also provides minimal water resistance and the small floor plan makes this boat easier for intermediate sailors to handle. Even though it offers a small footprint, this boat is sturdy enough to handle up to four adult passengers.

One of the best things about this boat plan is that it can be built almost entirely by using only common hand tools.

Of course, you can speed things up if you have power tools and you are skilled enough to use them correctly.

The Tern boat plan includes a 20-foot mast, but you can shorten that length if you desire. The plan includes a complete list of materials and step-by-step instructions on how to plane and assemble each element.

10. The Falcon

As you might expect from its name alone, the Falcon is an incredibly speedy sailboat for its size. It boasts a 14-foot centerboard and can handle two to four passengers, depending on its size and weight.

In tests of the original build, the creators claim that this boat out-distanced many Snipe and Comet sailing vessels as well as pacing evenly alongside longer 18-foot sailboats. When finished, your boat will have a six-foot beam and a total weight of roughly 475 pounds.

For the main framing components, they recommend using white oak and plywood will be the main material used in the hull construction. The hull features a V-shaped that was inspired by larger schooners.

The Falcon is best suited to sailing on bays, lakes, and wide rivers. It is also a boat plan with just under 120 square feet of deck space and it is a great build for amateur craftsmen and sailors.

11. The White Duck

The White Duck is a flat-bottomed rowboat with a total length of 13’6” and a four-foot beam. The cockpit is approximately 15 inches deep all the way around and this boat can handle up to five passengers while maintaining buoyancy and stability.

When fully constructed, it will weigh roughly 200 pounds, but the final weight will depend on the type of lumber you choose for your build. This boat plan features plywood planking over solid wooden frames.

The White Duck is built with a pointed bow that cuts nicely through the water. The flat stern of this boat design will make it easy to attach a small outboard motor with a maximum of six horsepower.

As you might expect from its name, this rowboat is a great option for duck hunting trips. That being said, it is a highly versatile craft that can also be used for pond fishing or casual rowing on your nearby lake.

12. The Sea Midge

The Sea Midge is one of the smallest rowboats on our list and it is ideally suited for one average-sized rower or two small paddlers. It is only about 8 feet in length and offers a 52-inch beam at its widest point.

The Midge’s small dimensions make her ideal for navigating narrower creeks and streams. With an approximate weight of 62 pounds, she is easy to maneuver on the water and can also be much more easily transported than some of the larger boat plans on our list

The Seamidge

13. The Zephyr

The Zephyr is a compact and speedy dinghy sailboat that measures roughly 14 feet long and approximately five feet across. This boat style was originally developed for safely crossing the English Channel. This means it can stand up well in rough waters.

When finished, it is also light enough to be transported on a small trailer or on top of a larger vehicle.

The boat plan calls for using hemlock or fir for the framing and oak or Douglas fir for the keel and chines.

14. The Gypsy

The Gypsy is a small cruising sailboat that is meant to be equipped with an outboard motor for powered locomotion. The original design resulted in an incredibly seaworthy vessel that logged more than 6,000 nautical miles in her lifetime.

It includes a comfortable cabin that makes it well-suited for multi-day sailing adventures. This boat plan includes improvements on the original design that will help you build an extremely durable and long-lasting sailboat.

The Gypsy boat design will help you construct a vessel that can handle a motor up to 25 horsepower so that you can enjoy cruising speeds of up to nine miles per hour.

While it may require a bit more of an investment in time and money, it will also help you produce one of the best boats you can build with a free boat plan!

15. The Crazy Cardboard Boat

PC Saint Dominic Catholic School

Finally, let’s talk about a crazy cardboard boat plan that you can build in less than a day. This is a great boat plan to bookmark for your next teambuilding project so that you can earn bragging rights with your coworkers.

The plan calls for using 1.5 sheets of cardboard. But you can use the remaining half sheet to build your own boat paddle if you want to get creative.

Triple-thick cardboard is best for this boat plan. But you can always double up thinner sheets if that is all you can find.

These plans include an easy-to-follow diagram for marking, cutting, and folding the cardboard sheets to create the hull of your boat. From there, it calls for using contact cement and construction adhesive to seal the edges and corners.

If you are looking to save a little money on this build you could also use duct tape and then wrap the entire design in plastic sheeting to provide waterproof qualities.

Overall, this build is one of the cheapest and easiest on our list. It is also a great project for hot summer camp days on the lake or river!

15 Free Boat Plans You Can Build This Week (with PDFs) – Final Thoughts

Photo by Alexandra Soloviova via Shutterstock

We hope that you now have a couple of free boat plans to inspire you to begin your own construction project.

Don’t hesitate to check out YouTube for some useful boat-building videos when you are getting into the nitty-gritty of these build processes!

Enjoyed 15 Free Boat Plans You Can Build This Week (with PDFs)? Share it with your friends so they too can follow the Kayakhelp journey.

Share on pinterest.

Peter Salisbury

Pete is the Owner of KayakHelp.com. Born and raised in Cleveland, Ohio, he grew up kayaking, fishing, sailing, and partaking in outdoor adventures around the Great Lakes. When he’s not out on the water, you can find him skiing in the mountains, reading his favorite books, and spending time with his family.

Affordable Sailboats You Can Build at Home

Last Updated by

Daniel Wade

September 13, 2023

‍ Key Takeaways

• There are many sailboats that anyone can build from home depending on tastes
• Budget will be the biggest deciding factor on a majority of the process
• Consider kits that come with most of what you need or choose ones that are all-inclusive
• Design complexities and new materials may make the building time process longer
• Plan the best you can ahead of time to save money and your working hours

‍ Buying a sailboat can be expensive, but building your own can save you money. So what are sailboats you can build from home?

Sailboats that you can build from home will likely be a small boat under 20 feet. These could be from many different boat suppliers such as B&B Yachts, Brooks Boat Designs, and Chase Small Craft. Boat plans will vary based on your budget and how much time you have on your hands.

Based on my previous experience, building your own boat will take much longer than if a professional were to do it. You also have to be able to study plans, consider various sailboat designs, and have tons of supplies such as fiberglass tape or fiberglass cloth. On top of that, you will also have to be good with your hands.

Table of contents

‍ Top 10 Affordable Sailboats Anyone Can Build at Home

Building your own pocket cruiser or other styles from boat plans is an impressive feat, as this will need dedicated time and money to assure your boat sails safely. Boat building takes a lot of patience as well, especially since this will not be completed in a fast manner.

Finding boat plans and materials that fit your budget will be key to being able to complete the project. The time it takes to complete these projects will vary on your overall experience and needs. Below are 10 of the most affordable sailboats that you can build in the comfort of your home.

B&B Yachts

B&B Yachts have 14 different boat plans you can choose from to find the boat of your desires. Their shop is located along the Bay River in North Carolina where they construct all of the kits and have a 100 foot dock to show off your project once you complete it.

One popular model to check out is their Core Sound 15, as it is the perfect size for those wanting to build a modest size boat for a handful of people on board. Their website features some videos of completed projects and the plans or kits for purchase.

• 14 different models to choose from plus some dinghies
• Various monohull and multihull options
• Friendly customer service with attractive prices
• Might be too many options for some that are indecisive
• Not ideal for those wanting to have a motor sailer

Brooks Boat Designs

Brooks Boat Designs has a handful of options to consider for your next sailboat building project. They are located in Brookline, Maine and give the option to buy the kits or have them build one from scratch for you. They have plenty of knowledge, so do not be shy to ask about modifications or custom features you are looking for.

Depending on your specifics, they can attempt to accommodate some of their plans to help fit your desired outcome. By checking out their site, you can see many examples of their construction in progress and what the boats will look like when completed.

• Offers a variety of kits
• Plans vary around $50 and up, while materials will obviously add more costs
• Some plans can be rowing boats that can convert to sailboats
• Might take a while to hear back from them, as their contact section is a little outdated
• Their plans may not accommodate a ton of extras for your taste

Chase Small Craft

Chase Small Craft offers a simple process for building boats. Their kits are equipped with everything you need and will help save you time than just buying the materials outright and other parts you could need. This is arguably one of the best bang for buck instances if you want to save time and money searching for pieces to your boat.

They are located in Saco, Maine and will ship everything to your home from there. All the necessary materials are included and all you need are the proper tools and working space.

• All-inclusive kits with what you need
• Tons of knowledge on their site for boat building
• Easy process to order and customize
• Complete kits can range over $20,000 for larger boats
• Kits may take up to eight weeks to ship out

Chesapeake Light Craft

You can expect high-quality boat kits from Chesapeake Light Craft . They feature 18 different sailboat kits that vary from eight to 20 feet in length. This should be more than enough to find one for you if you are newer to boat building.

They also have a wide variety of other kits in addition to the sailboat, in the event that you wanted to order a small kayak or paddleboard in addition to your sailboat. The prices vary considerably when considering a small or larger boat, so check the complete list of options to in order to potentially fit your needs.

• Plenty of sailboat offerings to choose from
• Different beautiful hull form options to consider
• Easy to build and perfect for sailing
• Only has basic materials needed for kit, so you may need to purchase other items
• Has epoxy shipping fee no matter if you pick up item

Dudley Dix Yacht Design

Dudley Dix Yacht Design has an extensive list of plywood and single skin sailing boat options. They have plenty of sail plans and kits to consider depending on your goals. These follow a classic look for sailboats, which are aesthetically pleasing.

If you are wanting one to accommodate a small family, they have more than plenty to look through. The cost is not as bad compared to others, but keep in mind that you may need to throw in your own supplies or specific tools to get the job done.

• Plans start at $30 and range up to $7,500 or more for kits
• More than enough of options to consider
• Affordable variety of sailboat offerings
• Might be too many options for those new to sailing
• Most are wood without the use of aluminum or steel

Farrier Marine

If you are in search of a multihull to build, then Farrier Marine is what you need. They offer a unique folding catamaran that is trailerable and give you the option to build it yourself. This not only makes it an appealing option, but anyone can take this multihull boat wherever they want with ease.

It features a thorough construction guide once you receive all of the materials. These also come with stainless steel fasteners and an aluminum mast for high-quality materials. Pricing will vary since you must request which model type you are considering.

• Ability to build a unique catamaran
• In-depth construction guide to help
• Easily handled and trailerable
• Price may be too high
• Limited offerings since only a few multihull options

Glen-L Marine Designs

Building a boat from Glen-L Marine Designs can save you time and money. They feature an easy system to order and receive the kits, as well as an in-depth guide to building them. This is an appealing option compared to most boat kit sellers.

The beauty about Glen-L is that anyone can build these from scratch, so you do not have to be the best boat builder in the world to get it done. They offer guides and helpful insights from their team to point you in the right direction. Plans vary around $15, while kits can range well over $1,000 depending on boat size.

• Nearly 50 designs to choose from
• Complete guide to help anyone build it
• Plenty of price points depending on size
• Might be overwhelming with the amount of options
• Could take a while to get parts since they are popular

John Welsford Boat Designs

John Welsford Boat Designs invites new and veteran boat builders that want a taste of quality small wooden boats. The boat plans are designed to meet your specifications and are catered to your desires.

There are seven sailboat designs to choose from so you do not feel overwhelmed in the process. However, they do not sell kits all the time, so you would need to have the materials or be on the lookout for the best prices when they are available.

• Seven sailboat plans with different sizes
• Quality boat builder and supporting community
• In-depth knowledge provided to you when you order
• Might be too small of boat size
• Kits are not always available

Iain Oughtred

There are plenty of options on the wooden boat store, but you should narrow down your search for Iain Oughtred’s line of sailboat kits and plans. There are 25 different plans to choose from, which should accommodate most everyone looking to build their own boat.

While they do offer some kits, they do not routinely offer sailboat kits. You would need to purchase all of the materials if you are considering one of their sail plans. Keep this in mind if you are considering, as you would need to hunt down the parts yourself.

• 25 different sailboat plans to look through
• Various sizes to contemplate for you sailing needs
• Prices will vary but are not bad compared to market
• No sailboat kits, only plans
• Newer boat builders might find too many options unappealing

Paul Gartside Boat Builder and Designer

Gartside Boats is a boat builder company based in Long Island, New York that showcases a variety of boats from traditional and newer methods of boat building. Within that variety, they have boat plans meant for six to 50 feet in length.

With an abundance of options, you will need to contact them regarding prices and any customizable options. Kits may vary as well, as they typically design in-house and build for you.

• Experienced boat designer that can accommodate with custom plans
• Many options are trailerable
• Can have plans for up to a 50 foot boat
• You will need to contact them for prices
• Customized options may make process more complicated for new boat builders

How Much Does it Cost to Build a Sailboat at Home?

As you have likely already done so, the math between building your own boat and buying one may be a huge difference. Likewise, you may even enjoy the challenge of taking an older boat that is gutted and restoring with parts from a kit to build one new again.

But how much does it cost exactly to build a boat from the comfort of your own garage or workshop? The prices are going to vary dramatically depending on your situation and material needed to get the job done. In addition, the time that it takes to complete this will also vary.

Sail plans are rather inexpensive if you are aiming to build a small boat. These plans allow you to see the workings of the boat design and what you need to build the boat.

Without these plans, you will not know the exact details of the design and it can cause major issues with the boat’s hull or other areas of the boat. Think of these as the backbone or instructions of the boat’s infancy before being built.

Price Per Square Foot

You should assume to pay anywhere between $300 to $600 per square foot if you are interested in building a boat. Buying a kit outright can be a good way to save time, but oftentimes these do not come with everything you need.

Instead, you should try to source as much of the materials at the best price as possible. Thinking ahead is part of the process and you might be able to score a deal at a lumber yard or hardware store for parts.

Boat Designs Matter

The design of the boat will be much different from one boat to the next, regardless if they are the same size in length. If you are pondering boats that range anywhere between 16 and 20 feet, you should factor in the shape of the hull, any rigging, and various appendages.

Prices tend to increase when there are more complexities within the designs. If you are considering a kit with more details than others, you will also have to pay more for the designs on that as well.

Kits Can Differ

It is important to understand that all kits are not going to be the same. As you gander at sailboat kits online to stitch together, you need to thoroughly look over to see if you have everything you need before buying.

It would also be at your advantage to ask the seller if any additional parts or supplies are needed. This may change your dynamic on the kit buying process and you may pass up one for another if it has everything you need. An all-inclusive kit may cost several hundred, if not thousands, of dollars more to have the convenience of everything in the bundle.

Construction Approaches

Some boat plans may require you to have certain tools to get the job done. This means special saws or planers, which the average person simply does not have.

Purchasing specialty tools might be expensive upfront and hard to find depending on what it is. Your best bet would be to check locally for others trying to sell their tools or consider a boat plan that does not require extensive tools to finish the job.

How Long Does it Take to Build a Sailboat?

An easy to build sailboat could take a while to build from scratch. Many different variances come into play that are difficult to pinpoint for everyone. But how long is that exactly and how will your experience play into this?

A fun project to sail in the wind could take you several months to well over a year depending on the boat plan and how big your boat is going to be. In addition, the materials all need to be accounted for prior to starting in the event a hardware store does not have them in stock.

Time Varies

The time that passes for simple boat designs on small sailing vessels can be done in a few weeks. This is assuming you have everything you need and work non-stop around the clock.

Certain complex situations may make the process long, such as the difficulty of working with some materials. If you are a skilled laborer, it may take you half the time compared to a novice. The amount of time it can take will vary on your availability and skill level.

Planning ahead will undoubtedly offer the most time-saving features. It also helps if you can tackle parts of the project at your own pace.

Complexity of Design

The design of the boat may make the construction process longer. For example, it may take you longer to build a catamaran compared to a similar lengthed monohull.

More complex designs might require more materials, therefore making the process a bit longer to complete. Furthermore, you will also need more experience working with difficult designs and that will affect you more as a newbie.

Be sure to manage your expectations well and do not allow yourself to become too stressed over this fun project. If you can, seek expert boat building advice from a local builder or the company you purchased sail plans through.

Quality Materials

The quality of the materials will matter significantly when building a boat and will greatly affect the time it takes to construct it. Handling fiberglass or carbon fiber might require specialty tools, while wood also demands a certain level of craftsmanship.

If you are not skilled at working with the material at hand, it might affect the quality of the build and you may have to go back to fix mistakes. This will definitely add more time to your project, because mistakes are bound to happen with your first project.

To save time, consider adding the tools and materials throughout the year or as often as your budget allows. You may want to try testing your skills on fiberglass or other materials to get a feel for how to work with it.

Related Articles

I've personally had thousands of questions about sailing and sailboats over the years. As I learn and experience sailing, and the community, I share the answers that work and make sense to me, here on Life of Sailing.

by this author

Best Sailboats

Learn About Sailboats

Most Recent

Best Small Sailboat Ornaments

September 12, 2023

Best Small Sailboats With Standing Headroom

December 28, 2023

Important Legal Info

Lifeofsailing.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon. This site also participates in other affiliate programs and is compensated for referring traffic and business to these companies.

Similar Posts

Discover the Magic of Hydrofoil Sailboats

December 11, 2023

Best Bluewater Sailboats Under $50K

Hunter Sailboats: Are They Built for Bluewater Cruising?

August 29, 2023

Popular Posts

Best Liveaboard Catamaran Sailboats

Can a Novice Sail Around the World?

Elizabeth O'Malley

June 15, 2022

4 Best Electric Outboard Motors

How Long Did It Take The Vikings To Sail To England?

10 Best Sailboat Brands (And Why)

December 20, 2023

7 Best Places To Liveaboard A Sailboat

Get the best sailing content.

Top Rated Posts

Lifeofsailing.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon. This site also participates in other affiliate programs and is compensated for referring traffic and business to these companies. (866) 342-SAIL

© 2024 Life of Sailing Email: [email protected] Address: 11816 Inwood Rd #3024 Dallas, TX 75244 Disclaimer Privacy Policy

How to Build a Boat: PM Constructs a 10-Foot Dinghy (With Plans)

A few months ago, home editor Roy Berendsohn tried his hand boat-building, making a 10-foot dinghy using old Popular Mechanics plans from 1937, hand tools and a cramped garage.

It was a long time since anyone in my family had built a boat. The last was my Uncle Paul. He was a shipbuilder who learned his trade beginning at age 14 in Hamburg, Germany. Every morning, the boy rowed from the family's dock out across the shipping lanes of the Elbe River, which flows into the North Sea. The trip to the shipyard where he was apprenticed took an hour and a half, longer in winter, when there was fog and floating ice on the water. After three years, Paul received a journeyman's certificate and a berth aboard a gigantic four-masted windjammer named Passat--"trade wind" in English. That was in the 1920s, be-fore the fascists confiscated his family's own small shipyard and the Berendsohns left for America.

A few months ago, I decided to try my hand at the ancestral trade. I've built everything from houses to a blacksmith's forge (March 2009), but there's no more evocative project than a boat, at least to me. Since before Austronesians first gazed across the Pacific, wooden vessels have stood for craftsmanship and the drive to explore. I sifted through PM's archives looking for a classic design and eventually settled on a 10-foot dinghy from our May 1937 issue. It looked elegant, yet simple enough to build on a pair of sawhorses.

It's been many years since my Uncle Paul was around to lend advice, so I ran the drawings past Timo White, a boatbuilder at Tuckerton Seaport, a small maritime museum on the New Jersey coast. It turned out that Timo was in the midst of restoring a surfboard built from plans in the July 1937 issue of PM. (It was a big year for seafaring projects, I guess.) He confirmed that the dinghy was a good candidate for a first-time builder and agreed to lend a hand if needed.

Shipyard in the Driveway

On a wintry early spring morning I set out for Willard Brothers Woodcutters, a sawmill and lumber dealer in Trenton, N.J. You can spend hours there, roaming stacks of delicious-looking walnut, cherry and oak, some of the boards as wide as your arm is long. I bought red oak for the Sea Scout's frames (that was the name of the craft in the plans, and I chose to keep it) and a 2-inch-thick slab of white oak for the wedge-shaped stem at the bow.

Back home, I started making a racket feeding planks through a table saw. My skills were creaky--I've spent too much time in recent years fixing stuff and not enough building--but over a few days my old confidence returned. The Sea Scout began to take form.

Most boats begin with the frames, the ribs that provide structure to the hull. I roughed them into shape, along with the stem and the gracefully shaped stern wall, or transom, which I cut from ¾-inch plywood. Then I braced it all to a building board--which is nothing more than a 2 x 10 with a chalk line marked down the center. The boat's skeleton was in place, but each member still needed to be precisely beveled before I could secure the curved planks of the hull. The next step was to clamp thin strips of wood, called battens, to the frame to stand in for the planks, so I could measure and mark all those angles. Then, I took the parts off the board and finished shaping them.

Often, the weather confined me to the garage, but when the sun emerged I worked in the driveway. If you want to get to know the neighbors, start building a boat. Linda from next door asked whether the craft would be sailed, rowed or powered by an outboard motor. Others wondered where I would go with it, how I'd get it there and what I would name it. A truck driver from Tulnoy Lumber, dropping off some marine plywood, approached respectfully. "This is beautiful," he said, with an old-fashioned New York accent as broad as the hand he ran over the frames.

Anatomy of a Boat

1. Building Board: Like most small wooden boats, the Sea Scout was built bottom side up. Most pieces aren't permanently connected until relatively late in the process, but every element of the frame had to be shaped to fit together precisely. The 12-foot-long building board, made from a 2 x 10, held the parts in the right positions while the bevels were measured and again when it was time to join the frames together with the chine logs and planking.

2. Bottom Member: The frames underlying the dinghy's hull were fashioned from red oak. The curved section is the bottom member--each one was cut with a jigsaw and smoothed using a block plane.

3. Side Member: The gently tapered oak side members meet the bottom members at a slight angle. These pieces are cut oversize, then shortened to finished length.

4. Gusset: The gussets joining the bottom and side framing members are cut from oak and fastened with epoxy and bronze screws, some of which ended up being too close to the gusset's edge.

5. Cross-Spall: Cross-spalls support each frame during the building process. They're screwed to the side members and the building board. After the planking is done, the boat is turned upright and the supports are removed.

Working the Plank

I don't know how Uncle Paul felt about it, but boatbuilding can be acutely frustrating. The bane of my weekends proved to be a small bronze screw. A No. 6 Frearson flat-head, to be exact. Like most modern DIYers, I'd been spoiled by drywall screws and other aggressive fasteners that practically plow into the lumber. Even using a specialized, tapered drill bit and a waxlike lubricant with the unlikely name of Akempucky, I managed to wreck screws by the dozen. The head on one would strip a moment before the screw was fully seated, while another would shear off on the last eighth of a turn, leaving me with a shiny Frearson-head penny.

Timo had tried to downplay the arcana I'd face--"It's more like house carpentry than fine-furniture building," he had said--but I still found myself floundering on occasion. One challenge was that the 1937 article was more an overview than a detailed set of plans. And, though it pains me to find fault with my forebears at Popular Mechanics, the sketch contained suspicious discrepancies. Timo helped me recalibrate some of the dimensions midway through the project--and I had to trim several pieces after they were assembled.

The biggest hurdle came when it was time to plank the hull. The classic way is to bend strips of solid wood to the frames. I'd chosen marine-grade fir plywood instead to save time, but now I was barely able to force the hull's 14-inch sheets into place. There was no way the half-inch plywood I'd planned for the bottom was going to work.

Timo advised me to switch to a special, wafer-thin marine-grade plywood and plank the bottom in two layers. He came swooping in one Thursday morning to show me the technique. He stepped out of his truck with a broad smile, and a block plane in each hand, and my mood lifted. He politely took a sighting down the chine logs where we'd attach the bottom, and spent a few minutes planing them to the last measure of precision. Then we got to work with staples, glue and screws--and in a couple of hours the project went from a plywood flower bed to a small craft with sensuous compound curves.

It was satisfying, but my mistakes still showed in details like the placement of screws and the shape of the stem. "You know what they say," Timo told me. "Putty and paint makes a boat what it ain't." I got out my paintbrushes.

1. Very few elements in a boat are simply cut to shape and installed. Like the oak stem shown here, nearly every piece needs to be beveled or curved to fit the surface it meets. (That tool is a fore plane I own, built by Stanley Tools in 1927.)

2. Ancient terms persist in boatbuilding. This curving wood piece, where the bottom is attached, is called a chine log. In past centuries, it consisted of a single log chosen for its natural curve, then shaped to fit. The chine log is set in a notch and fastened to each frame.

3. Two layers of okoume plywood form the bottom of the Sea Scout. Timo (foreground) showed me how to install them.

4. The Sea Scout motored along nicely, powered by this 2.5-hp four-stroke Mercury Marine outboard.

Maiden Voyage

We launched the boat at Tuckerton Seaport on a cool, overcast day that felt more like September than June. Down at the dock, Timo produced a can of Amstel Light in lieu of champagne. "Go ahead," he said, "pour it over the bow." I popped it open and emptied the beer over the paint. "I christen thee Sea Scout," I said. Then we slid the little craft off the dock and into the water.

You might think a feeling of triumph came over me. Not so. The Sea Scout looked very small, almost helpless, as she sat bobbing at the end of the painter, the little rope that Timo had threaded across the bow. I felt humbled. A phrase from the Book of Psalms flashed in my mind: "They that go down to the sea in ships, that do business on great waters."

I wasn't aiming for any great waters myself. I eased off the dock and into the boat. Timo handed me the oars. Awkwardly, I drew the handles back, just above my hips. The craft slid forward gracefully, almost like she was on ice. As Timo watched, I braced the left oar down in the water and swept the surface with the right. The Sea Scout pivoted neatly, unexpectedly elegant and spry.

If the oars were a kick, you can imagine the thrill I felt when I mounted the 2.5-hp Mercury Marine outboard on the transom. It's a clean-running four-stroke engine, compact yet almost zippy on a boat this small. I gave the engine full throttle and cut some nice straight lines and a pleasingly tight curve complete with a crisp little wake.

With the afternoon gone, my first voyage was complete. In the end, I decided to donate the boat and engine to Tuckerton Seaport. Frankly, I needed the space in my garage and driveway: The Sea Scout was a good first foray into wooden boatbuilding, but I knew I could do better--and I'm already sifting through plans.

Roy Berendsohn has worked for more than 25 years at Popular Mechanics, where he has written on carpentry, masonry, painting, plumbing, electrical, woodworking, blacksmithing, welding, lawn care, chainsaw use, and outdoor power equipment. When he’s not working on his own house, he volunteers with Sovereign Grace Church doing home repair for families in rural, suburban and urban locations throughout central and southern New Jersey.

.css-cuqpxl:before{padding-right:0.3125rem;content:'//';display:inline;} Ask Roy .css-xtujxj:before{padding-left:0.3125rem;content:'//';display:inline;}

How to Stain Pressure-Treated Wood

How To Get Leaf Stains Off Your Wood Deck

Are Bottle Rockets a Serious Fire Danger?

How To Cut Drywall With a Tape Measure and Knife

What Causes That Condensation on my Ceiling?

What You Need to Know About GCFI Outlets

How Often to Pump a Septic Tank

What Is This Thumping Noise in My House?

Backup Generator, or Backup Battery?

Why Your Christmas Lights Are Flickering

Can the Power Company Trim Your Trees?

• Accessories
• Built Boats
• Information
• Rowing Boats
• Sailing Boats
• Motor Boats
• Surf and Paddle Boards

Sailing Boat Plans

Madness Pacific Proa

A lightweight Pacific proa for fast cruising or daysailing.

More information

Tenderly Dinghy

A traditional-looking 10-foot clinker dinghy for rowing, sailing and motoring that is stable, handsome and easy to build.

Eastport Pram

A pretty, light, tough, roomy and easy to build 7 foot 9 inch pram dinghy that can be rowed or sailed.

Nesting Eastport Pram

An easy to build rowing and sailing pram dinghy that splits into two nesting sections for compact storage.

A 15 foot clinker style double ended family boat that can be rowed, sailed or motored.

Skerry Raid

A small, decked, wooden cruising boat for coastal expeditions by sail and oars.

Lighthouse Tender

A stable but fast double-ended rowing or sailing boat based on a traditional Maine Peapod.

Northeaster Dory

A 17 foot clinker dory for solo or tandem rowing or sailing.

Southwester Dory

A lightweight beach cruising and expedition boat for sailing, rowing and motoring, which can also be built as a motor launch without the sailing rig.

The Duo is a simple-to-build rowing and sailing dinghy that can nest for easy storage. It makes a good tender as well as a fun sailing dinghy.

Jimmy Skiff II

A stable, flat-bottomed rowing and sailing boat that also handles well under motor, for family outings, fishing and day sailing.

Goat Island Skiff

A simple lightweight sailing boat with excellent performance.

PassageMaker

An 11 foot 7 inch clinker style pram dinghy that performs beautifully when rowed, sailed or motored.

PassageMaker Take-Apart

An 11 foot 7 inch clinker style pram dinghy that can be nested to save space.

Pixie Beach Catamaran

The Pixie is a fun car-toppable beach catamaran that sails well with one or two crew and is popular among people who are new to sailing catamarans but who are not that interested in racing.

A fast-sailing 15 foot cabin cruiser with a dry and commodious interior.

Autumn Leaves Canoe Yawl

A modern wooden canoe yawl for engineless coastal cruising by sail and oars, designed to be affordably built by an amateur.

Faering Cruiser

A serious rowing and sailing boat for coastal cruising, with a small cabin aft.

Nesting Expedition Dinghy

A very compact sailing beach cruiser that can be nested in three sections for storage in a corner of a garage.

Mbuli Pacific Proa

Plans for a very light and fast Pacific proa beach cruiser.

A versatile nesting dinghy for day sailing and camp cruising with a comfortable double berth.

Outrigger Junior

A finely-proportioned and lively sailing canoe with a huge lateen sail for lots of speed.

Quattro 14 Beach Catamaran

A lightweight single-trapeze beach catamaran for racing that is easy to build.

Quattro 16 Beach Catamaran

A high performance twin-trapeze racing catamaran that is lightweight and easy to build.

Strike 15 Trimaran

The Strike 15 is a high-performance racing trimaran with folding outriggers designed to be easy to sail by older or less experienced sailors and easy to launch from the beach.

Strike 16 Trimaran

The Strike 16 is a dry, comfortable trimaran for four-person day-sailing or two-person weekending.

Strike 18 Trimaran

The Strike 18 is a dry, comfortable trimaran for family day-sailing with an optional, removable, cabin top to convert it into a pocket cruiser.

Tryst Trimaran

A light and stable 10 ft trimaran that is very easy and fun to sail and can nest for compact storage.

Zest Racing Dinghy

The Zest is a single-handed racing dinghy with a plywood hull and comfortable sitting-out wings.

Beth Sailing Canoe

A light sailing canoe combining a traditional rig with a high speed hull.

Kombi Sailing Canoe

A truly dual-purpose wooden canoe for exciting sailing and family paddling.

Viola Sailing Canoe

A lightweight plywood sailing canoe with the performance and stability of a good sailing dinghy.

A low-cost sailing dinghy that is easy to build and fun to sail for clubs, regattas and sailing lessons.

A pretty little demountable trimaran designed for speed and easy handling by one or two people on lakes, rivers and bays.

TriRAID 560s

A light and fast adventure trimaran for 1-2 people designed for raid competitions.

Sailing Outriggers

Outrigger floats to turn a canoe or kayak into a fast sailing trimaran.

Drop-in Outrigger Plans

Light and easily removable outrigger floats that turn a canoe or kayak into a formidable sailing boat or a stable fishing platform.

Mini Drop-in Outrigger Plans

Small outriggers for a sailing canoe, to aid stability for learners and for extra safety for more adventurous sailing.

Drop-in Canoe Sailing Rig Plans

A simple lug rig that can be added to an ordinary canoe or kayak to add the ability to sail.

• Fyne Boat Kits — Old Cooperage Yard, Gatebeck, Kendal, Cumbria LA8 0HW
• Telephone: +44 (0)1539 567 148
• Email: info [at] fyneboatkits.co.uk

Copyright © Fyne Boat Kits

July / August Issue No. 299  Preview Now

Plans & Kits

If you’re in the market for a boat to build, this directory of Boat Plans & Kits is a fine place to start. And if your company sells plans or kits, we invite you to list your offerings here. There is no charge for listing, but the featured boats must be built of wood. To refine your search of this directory, use quotation marks. If you search Nutshell Pram Kit, you’ll receive all the listings that include the words Nutshell, Pram, and Kit. To refine your search, enter “Nutshell Pram Kit”; you’ll then see only the results for Nutshell Pram kits.

Post Your Boat Plans & Kits

Post Your Plans/Kits login or register

Search plans & kits.

To refine your search, add quote marks. If you search Nutshell Pram Kit, you will get all the listings which include Nutshell, Pram, and Kit. To refine, search “Nutshell Pram Kit” and you’ll see just Nutshell Pram Kit results.

717 Results

Trawler Yacht Workboat 36

NEW - COASTER Trawler Yachts & Work boats Here are the first of a new range of Coastal Trawlers that can customized to suit your desires and particular requirements. All will be excellent sea boat

Sailboats - Daysailers

Strike 18 sailing trimaran.

The 18ft STRIKE is a sailing trimaran design that uses a 16ft beach cat as the outriggers/amas and rig. The main hull is plywood and has a dory shape that is extremely easy to build.

Sailboats - Racing

We chose the 9.1 mt LOA not to overcomplicate its construction, but to facilitate the availability of a place to build this boat, and at the same time to have internal volume that allows a comfortable cruise.

Oar / Paddle

“Breeze” is a 10′ (3m) double paddle canoe. Two sheets of plywood needed. Stitch and glue construction using 3″(75mm) fiberglass tape in epoxy for all seams inside and out. The deciding factors when designing the boat were mostly the same as with all my designs - seaworthiness and lightweight.

Motorboats - Outboard

21' runabout.

When I first saw WoodenBoat Magazine’s boat design competition to design a modern wooden runabout, I was very excited. I’m sure most of the other competitors in this competition feel the same way.

Sailboats - Cruising

Lion 550 adrenaline.

Lion 550 Adrenaline, light boat, trailer envelope can significantly expand the geography of travel and take the owners a lot of positive emotions and adrenaline.

25' Sea Bird Yawl

A simple and seaworthy V-bottomed centerboard cruiser with accommodations for two.

Construction: Plywood planking over sawn frames

Lofting is required

Plans include 10 sheets.

20' Spalding Utility Launch

Rugged little launch with generous beam.

Construction features a traditional backbone of bolted-up oak, steam-bent frames and strip-planking. Four different arrangements are shown.

Construction: Strip-planked over steam-bent frames.

28' Bermuda Runabout

The longest runabout we offer, this 28' high-speed, triple cockpit runabout will also require highly skilled builders, but oh, the rewards...

Construction: Battened-seam planking over sawn frames.

Lofting is required.

Plans include 3 sheets.

Harbor Woodworks offers custom kits and boats, tailored to your specifications and desired level of completion. We ship to the U.S.

Share your boatbuilding plans or kits today.

Login Sign up

From the Community

Handmade wooden canoe

Beautiful hand built wooden canoe. Design modeled on the Wabanaki Indian canoes of Maine.

1929 Hacker Craft Runabout 18'

Jimmy Steele Peapod

Good Vintage Boat - Hull Number 66 - Completed In 1989.

Boats Plans and Kits

Switzer Bullet 136

From online exclusives.

The final voyage of STAVANGER

Extended content.

STELLA MARIS

Aboard WESTER TILL

• BOATBUILDING SUPPLIES
• Aluminum & Steel Powerboats
• Aluminum & Steel Work Boats
• Classic Dinghy - Cedar Strip
• Classic Mahogany Runabouts
• Classic Runabouts
• Hydroplanes - Inboard
• Hydroplanes - Outboard
• Kayaks - Fabric Covered
• Kayaks - Plywood
• Powerboats 10'-16'
• Powerboats 18'-26'
• Sailboats - Monohull
• Sailboats - Multihull
• Sport Runabouts
• Tunnelhulls

Your shopping cart is empty!

Sailboat Plans 18-30ft

Bruce Roberts sailboat designs

Boat plans 18 - 30 ft .

This section of Bruce Roberts sailboat designs and boat plans cover the following vessels in the range of 18 to 30 foot. The Roberts, Adventurer, Tom Thumb, and Canoe Stern. Boat building plans using steel, aluminium, fiberglass wood/epoxy, depending on the design, are available. Information and prices are on each individual design page.

Study Plan Packages contain all the sheets #1 from the actual plans. Sail Plans and the various accommodation layouts pertaining to the design are shown on these sheets. There may be anywhere from two to eight #1 sheets which are all to scale and which measure between one meter and two and a half meters long each. They are intended as a more in-depth overview of the design in which you are interested.

Material Lists for the basic materials required to build the hull, deck and superstructure are included in the study plan package to help you with your budgeting. Where Fibreglass is mentioned as a material this means Balsa sandwich / Foam sandwich, Single skin or C-Flex. Most steel plans can be adapted to aluminium construction. Both moulded ply and strip plank can be used in conjunction with the wood epoxy saturation method. Sail and rig details are also shown on the study plan sets.

As the Study Plan Packages include the basic measurements in scale for the accommodation layouts, you can customize the layouts to suit your needs if what is presented is not exactly to your liking.

The link to download the Study Plan Packages is emailed to your email address and generally within 24 hours, The link to the Full Plan Sets is also generally emailed within 24. All study plans and full plan sets are downloadable in .pdf format for you to have printed at a nearby print shop. The study and full plan sets are available on CD's on request with postage cost depends on country.

To View drawings , photos, information and prices of the design that interests you just click on that design.

Payments : We only accept payments through PayPal. This method of payment protects both of us. Please be aware that there is no obligation or need to be a member of PayPal to use them to pay us using the normal various methods of payment.

Pram Dinghy Boat Plan

Roberts Pram Dinghy This Pram dinghy can be built in fiberglass or plywood. The pictures sho..

Adventurer 18 Trailer Sailer Boat Plan

Roberts Adventurer 18 Trailer Sailer This design is available as two different concepts, Version ..

Adventurer 19 Trailer Sailer Boat Plan

Roberts Adventurer 19 Trailer Sailer This design is available as two different concepts, Version ..

Adventurer 22 Trailer Sailer Boat Plan

Roberts Adventurer 22 Trailer Sailer This trailerable sailboat has been very popular and performs..

Adventurer 24 Boat Plan

Roberts Adventurer 24 This sailboat has been very popular and is a joy to build and sail. Suitabl..

Adventurer 24 Trailer Sailer Boat Plan

Roberts Adventurer 24 Trailer Sailer This trailerable sailboat has been very popular in both it's..

Tom Thumb 24 Boat Plan

Roberts Tom Thumb 24 Designed by Canadian Graham Shannon this boat was originally designed to be ..

Roberts 246 Boat Plan

Roberts 246 This sailboat has proved to be an exciting little boat to sail. The drop keel version..

Adventurer 25 Trailer Sailer Boat Plan

Roberts Adventurer 25 Trailer Sailer Over 1,000 examples of this design have already been complet..

Tom Thumb 26 Boat Plan

Roberts Tom Thumb 26 Although an enlargement of the Tom Thumb 24 the Tom Thumb 26 is a completely..

Roberts 27 Boat Plan

Roberts 27 This nifty earlier design is available for either fibreglass or wood epoxy constructio..

Roberts 28 Boat Plan

Roberts 28 Designed for multi-chine steel construction only, this design is available with both l..

Roberts 29 Boat Plan

Roberts 29 Another early design that still makes for a pleasant, safe, family yacht that is easy ..

• Row boat plans
• Sailboat plans
• Power boat plans

Row boat plans 10-14 ft

Questions? Suggestions? Contact us at: [email protected]

• Plans & Kits
• Plans by designer
• Paul & Marya Butler

10 Foot Norwegian Pram Plans PDF

Write a review.

• Create New Wish List

Description

Additional information.

For printed plans, click HERE

A sailing pram for double diagonal strip construction

The 10 foot Norwegian Pram is a nicely expanded version of the compact 8 footer, and provides 35 square feet of sail instead of the 8 footer 's 28 square feet. Construction techniques are the same.

Related Products

8' Norwegian Pram Plans PDF

10 Foot Norwegian Pram Printed Plans

8' Norwegian Pram Printed Plans

Piccup Pram Plans PDF

Ultra-Pram Plans PDF